KAMPALA INTERNATIONAL UNIVERSITY

COLLEGE OF APPLIED SCIENCE AND TECHNOLOGY

SCHOOL OF COMPUTING AND INFORMATION TECHNOLOGY DEPARTMENT OF INFORMATION TECHNOLOGY.

 

 

A REPORT ON FIELD ATTACHMENT/INTERNSHIP AT AFROSOFT IT

SOLUTIONS UGANDA LIMITED FROM

JUNE 06TH – 30TH JULY 2016

BY

 

CHELIMO COLLINS CHESHEWA

Chelimo.collins71@gmail.comS BIT/44982/143/DU

 

FIELD ATTACHMENT REPORT SUBMITTED TO THE COLLEGE OF APPLIED

SCIENCE AND TECHNOLOGY IN PARTIAL FULFILLMENT OF THE

REQUIREMENTS FOR THE AWARD OF DEGREE IN  INFORMATION TECHNOLOGY

 

 

MRS. KABANDA PAULINE

ACADEMIC SUPERVISOR

SCHOOL OF INFORMATION AND COMPUTING

KAMPALA INTERNATIONAL UNIVERSITY

 

 

 


DECLARATION

 

I chelimo Collins cheshewa hereby declare to the best of my knowledge that this report was prepared and edited as a result of my own effort in attendance, participation and understanding from my internship training at Afrosoft IT solution limited submitted to the college of applied science and technology Kampala international university under the guidance of my field supervisor Mr. Ssentamu Semeo and the results embodied in this Report have not been submitted to any other University or Institute for the award of a degree, certificate or diploma in the particular field of study.

 

Signature………………………………………………………

 

 

Date……………………………………………………………. 

 

 

 

 

 

 

APPROVAL

 

This is to certify that this internship report has been prepared and submitted by chelimo Collins cheshewa upon completion of his eight weeks industrial training period at Afrosoft IT solutions limited and was submitted for the examination with the approval of Mr. Ssentamu Simeo who is my field supervisor and is now ready for submission to the school of computing and information technology at Kampala International University.

 

FIELD SUPERVISOR

MR. SSENTAMU SEMEO

 

…………………………..

 

 

ACADEMIC SUPERVISOR

MRS KABANDA PAULINE

 

……………………….

 

 

 

 

ACKNOWLEDGEMENT

 

I chelimo Collins cheshewa sincerely thankful to all those people who have been giving me all the necessary kind of assistance in the making of this report.

I express my gratitude to the field supervisor Mr. Ssentamu Semeo who has through his vast experience and knowledge been able to guide me, both ably and successfully towards the completion of the report. I express my gratitude to the school of computing and information technology Kampala international university especially the department of computer science.

I would hereby make most of the opportunity by expressing my sincerest thanks to my academic supervisor Kabanda Pauline and all my faculties whose teaching gave me conceptual understanding and clarity of comprehension, which ultimately made my report easy to write. Credit also goes to all my friends whose encouragement kept me in good stead. Their continuous support has given me the strength and confidence to complete the report without any difficulty.

I would also like to acknowledge my gratitude to the team at Afrosoft IT Solutions without whom this report would have been incomplete.

 

 

 

 

DEDICATION

In the first instance, I offer my holly and diligent respect to the Almighty God for the life, wisdom, courage and endurance he gave me. God you are the God of providence, wealth, Wisdom and for this, I humbly offer my gratitude to you.

I also extend my gratitude to my beloved mother for the care and my beloved relatives and friends. In a special way I acknowledge my brother Mr. muzungyo Allan mark for the valuable time and guidance he extended to enable me to complete this report.

I wish to dedicate this report to my beloved parents, sisters, brothers and family Mrs. Cheptoyek lovisa, kwemboi Amos, chemutai Shedrack for their continued love, care, Financial support in my academic advancement during the all course of my study and also thank them for the good moral support they gave me, I just pray to the almighty God to give them the best on earth and grant them with paradise on here after and finally. I place my gratitude to my friends with whom I shared knowledge and resources during my internship period especially Kalungi benard and Kahigwa Ibrahim.

 

 

 

 

 

 

 

 

 

ABSTRACT

THIS Report gives an account of all activities that I did and how they were done during the time doing internship training with Afrosoft it solutions limited. This report also covers the experience and skills which were acquired during the specific period of training including the challenges and emerging issues

Chapter two gives details of the roles and duties I was assigned to perform at Afrosoft IT solutions limited and they include computer repair and maintainace, website designing using WordPress, Moodle designing, networking administration, windows server 2008 R2, graphics and design.

Chapter three gives details of proficiencies gained in carrying out the tasks during internship period (skill) areas of knowledge accumulated in the field (experience) and areas of learning out of exposure, discovery out of knowledge

Chapter four gives details about the recommendations and conclusions

 

 

 

 

 

 

 

 

LIST OF ACRONYMS

 

CPU

CENTRAL PROCESSING UNIT

CRT

ATHODE RAY UBE

DHCP

DYNAMIC HOST CONFIGURATION PROTOCOL

DVD

DIGITAL VERSTILE DISK

ESD

ELECTROSTATIC DISCHARGE

FP

FRONT PANEL

HDD

HARD DISK DRIVE

ICS

INTERGRATED CIRCUITS

ICT

INFORMATION AND COMMUNICATION TECHNOLOGY

IT

INFORMATION TECHNOLOGY

LCD

LIQUID CRYSTAL DISPLAY

MROM

MASK READ ONLY MEMORY

ODD

OPTICAL DISK DRIVE

PCB

PRINTED CIRCUIT BOARD

PSU

POWER SUPPLY UNIT

RAM

RANDOM ACCESS MEMORY

ROM

READ ONLY MEMORY

SATA

SERIAL ADVANCED TECHNOLOGY ATTACHMENT

TFT

THIN FILM TRANSISTOR

ZIF

ZERO INSERTION PACKET

 

 

 

 

Contents

DECLARATION..................................................................................................... i

APPROVAL.......................................................................................................... ii

ACKNOWLEDGEMENT......................................................................................... iii

DEDICATION...................................................................................................... iv

ABSTRACT........................................................................................................... v

LIST OF ACRONYMS............................................................................................ vi

1  CHAPTER ONE.................................................................................................. 1

1.1  Introduction............................................................................................................................. 1

1.2  BACKGROUND OF THE FIELD ATTACHMENT............................................................................... 1

1.3  OBJECTIVES OF THE FIELD ATTACHMENT................................................................................... 1

1.4  BACKGROUND OF THE ORGANISATION OF FIELD ATTACHMENT.................................................. 2

1.5  LOCATION................................................................................................................................ 2

1.6  VISION..................................................................................................................................... 2

1.7  MISSION.................................................................................................................................. 2

1.8  VALUES OF THE COMPANY........................................................................................................ 3

1.9  OBJECTIVES OF THE ORGANIZATION.......................................................................................... 3

1.10  THE STRUCTURE OF THE ORGANISATION................................................................................. 4

1.10.1  Directorate...................................................................................................................... 5

1.10.2  Director........................................................................................................................... 5

1.10.3  Operations Manager......................................................................................................... 5

1.10.4  Receptionist..................................................................................................................... 5

1.10.5  Software development manager....................................................................................... 5

1.10.6  Marketing personnel........................................................................................................ 5

1.10.7  Software developers......................................................................................................... 5

1.11  THE MAIN ACTIVITIES OF THE ORGANISATION.......................................................................... 5

1.11.1  ONGOING PROJECTS......................................................................................................... 6

2  CHAPTER TWO................................................................................................. 7

2.1  INTERNSHIP PROGRAM DESCRIPTION AND NATURE OF WORK.................................................... 7

2.1.1  INTERNERSHIP DESCRIPTION............................................................................................... 7

2.1.2  NATURE OF WORK............................................................................................................. 7

2.1.3  DISASSEMBLING COMPUTER COMPONENTS...................................................................... 11

2.1.4  Assembling computer components................................................................................... 12

2.1.5  Steps followed when assembling a computer..................................................................... 13

2.2  DESIGNING A WEBSITE USING WORDPRESS.............................................................................. 15

2.2.1  INSTALLING WORD PRESS................................................................................................. 15

2.3  Configuration and installation of windows 7 operating system.................................................. 18

2.3.1  Installing windows 7 operating system from a DVD............................................................ 18

2.4  Windows server 2008 R2......................................................................................................... 18

Installing windows server 2008 R2......................................................................................... 18

2.5  NETWORKING......................................................................................................................... 20

2.5.1  TRANSMISSION MEDIA..................................................................................................... 20

2.6  GRAPHICS AND DESIGN........................................................................................................... 27

2.6.1  ADOBE PHOTOSHOP......................................................................................................... 27

2.6.2  LAUCHING ADOBE PHOTOSHOP CS.................................................................................... 27

2.6.3  CREATING A PROJECT....................................................................................................... 27

2.6.4  CUTTING A PHOTO........................................................................................................... 27

2.6.5  HOW TO DELETE BACKGROUND........................................................................................ 27

2.6.6  BRUSHING ROUGH OBJECTS.............................................................................................. 27

2.7  ILLUSTRATOR.......................................................................................................................... 27

2.7.1  DESIGNING A CALENDER................................................................................................... 27

2.8  MOODLE................................................................................................................................ 27

2.8.1  INSTALLATION.................................................................................................................. 28

2.8.2  ENHANCING THE MOODLE................................................................................................ 28

3  CHAPTER THREE............................................................................................ 29

3.1  ACHIEVEMENTS...................................................................................................................... 30

3.2  CHALLENGES.......................................................................................................................... 31

4  CHAPTER FOUR.............................................................................................. 32

4.1  RECOMMENDATIONS.............................................................................................................. 32

4.1.1  THE UNIVERSITY............................................................................................................... 32

4.1.2  THE STUDENTS FOR FUTURE INTERNSHIP........................................................................... 32

4.1.3  THE ORGANIZATION......................................................................................................... 32

4.2  CONCLUSION.......................................................................................................................... 33

 

 

 

TABLE OF FIGURES  

Figure 1:      LCD monitor .............................................................................................................................. 7 Figure 2: computer case ................................................................................................................................ 8 Figure 3: keyboard ........................................................................................................................................ 8 Figure 4:mouse ............................................................................................................................................. 8 Figure 5:motherboard ................................................................................................................................... 9 Figure 6:power supply unit ......................................................................................................................... 10 Figure 7:hard disk drive............................................................................................................................... 11 Figure 8: screenshot of how to create a database. .................................................................................... 16 Figure 9:screenshot of installation of windows server 2008 R2 ................................................................. 19 Figure 10: router ......................................................................................................................................... 23 Figure 11 showing how routers work. ........................................................................................................ 23 Figure 12: Switch ......................................................................................................................................... 23 Figure 13 showing how a switch works. ..................................................................................................... 24 Figure 14: Hub ............................................................................................................................................. 25 Figure 15 showing how to configure the OSPF protocol ............................................................................ 26

 

 


1 CHAPTER ONE

1.1 Introduction

The purpose of this report is to introduce and explain my field attachment/internship program at Afrosoft IT solution Uganda limited starting June 06th to August 2016. It will mainly uncover the background, mission, vision, objectives, structure, strength, opportunities and challenges faced by the organization. It is hoped that this report would serve as a cardinal vehicle to the improvement of the internship program.

1.2 BACKGROUND OF THE FIELD ATTACHMENT

Field attachment may be defined as a field based practical work carried out by students with the help of their supervisors for the purpose of acquiring the necessary skills within their fields of attachment. Or, it`s the field based practical work carried out by staff and students for the purpose of teaching and /or research in places outside the university control but where the University is responsible for the necessary safety of its staff, students and others exposed to their activities. The intention of the field attachment is to enable me as a student to get a chance to apply the knowledge and information I acquire as a student to the real-life of work which will enable me acquire some skills and experience from the field of work

1.3 OBJECTIVES OF THE FIELD ATTACHMENT.

Some of the major objectives of the attachment include;

•      To enable me get a first-hand experience, skills and work-life in the field which may be of use after my graduation.

•      To develop more understanding about workplace behaviors (ethics), work responsibilities and their challenges

•      To provide an opportunity to me as a student to apply the techniques I have theoretically and practically learnt while at the university to solve problems that I tend face.

 

 

Specific Objectives;

•      To enhance & strengthen linkages between Kampala international University & various stakeholders.  

•      To provide an opportunity for students and academic staff to interact with the stake holders and potential employers to appreciate field situations that will also generate information for curricula review and improvement.

1.4 BACKGROUND OF THE ORGANISATION OF FIELD ATTACHMENT

Afrosoft IT solutions Uganda limited is a software development company which was founded in 2008 under the management of Mr. Katamba Ronald as the Director, upon his representation of east and south Africa in the Microsoft imagine cup competition in France when he was in his second year in the university. The company is a software development company delivering value proposition through quality process and people at the core of Airsoft’s business practices with emphasis on productivity results in reduced costs of development and maintainace projects. 

1.5      LOCATION.

Afrosoft IT solutions Uganda limited is located on Plot 28/30, Bombo Road, Teachers house 1st floor, P.O. Box 4629 Kampala, Uganda. Telephone 0785-856-863/0703-034758. Email:info@afrosoftug.com. web: www.afrosoftug.com. 

1.6 VISION

To lead in the various avenues of software outsourcing market, implement novel ideas in project development and deliver cost effective and required solutions to its prospective clients.

1.7 MISSION

   To earn global admiration as IT outsourcer, by building and maintaining long lasting relationships with people and technology and deliver functional software and excellent services 

 

1.8  VALUES OF THE COMPANY

•      Client intimacy.

•      Confidentiality with respect to work.

•      Reflective atmosphere.

•      Integrity expressed.

•      Bonding relations with clients.

1.9 OBJECTIVES OF THE ORGANIZATION

•      To trim down the cost and risk of software development.

•      To boost the quality of applications, development methods and tools.

•      To attain faster time to market with shorter development life cycle.

•      To strengthen the ability to handle service level commitments.

•      To achieve faster time market to applications.

•      To leverage the proven power of sun architecture’s finest practices, methodology, patterns and framework.

 

 

 

 

 

 

 

 

 

 

1.10 THE STRUCTURE OF THE ORGANISATION

 

 

 

 

 

 

 

Description of the organization structure

1.10.1 Directorate

An overseer of the organizations activities and is the main signatory to all the company external activities.

1.10.2 Director

Responsible for external activities of the company

1.10.3 Operations Manager

Manages the day to day activities of the company

1.10.4 Receptionist

He is responsible for handling all financial transaction of the company and customer care

1.10.5 Software development manager

Ensures   quality software before marketing 

He is responsible for business’s outsourcing for the company

1.10.6 Marketing personnel

Responsible for making the company not only to clients but also in the environment

1.10.7 Software developers

Responsible for producing company software’s

 

 

 

 

 

 

 

 

 

 

1.11 THE MAIN ACTIVITIES OF THE ORGANISATION

•      Software development, upgrade and maintenance.

•      IT consultancy.

•      ICT innovations.

•      Database solutions and upgrade.

•      Website and desktop application development.

•      Mobile application development.

•      Hardware repair and software maintainace.

•      Network administration and IT support.

•      Graphics design.

•      Business outsourcing.

•      Linux and Unix administration (Virtualization and server configuration).

•      Computers, laptops and project hire.

1.11.1 ONGOING PROJECTS

 

Ø  Prison and prison Management System for Uganda prison

Ø  Mobile SMS application for ESAFF (Eastern and South African Farmers Forum Uganda

Ø  Support system for provision of general support to UOSPA (Uganda Oil Seeds Producers Association)

Ø  Configuring share point server2010, exchange server 2010 and creating a workflow for Nation Council of science and Technology. Ø NTV sales management system

Ø  NBS TV website and Mobile Application

Ø  DNA analysis system

Ø  Psaver 

 

 

 

 

 

 

2 CHAPTER TWO

2.1 INTERNSHIP PROGRAM DESCRIPTION AND NATURE OF WORK

2.1.1 INTERNERSHIP DESCRIPTION

This chapter describes the nature of work that I involved myself as I was in the organization. It shows the activities that I did and describing how exactly I performed such work.

2.1.2  NATURE OF WORK.

The nature of work or activity that I carried out in my internship included Identifying the core components of a computer, computer Maintenance and Repair, disassembling and reassembling system units, networking using the routers and switches and other network devices.

2.1.2.1    COMPUTER HARDWARE AND SOFTWARE MAINTENANCE

This includes activities like identifying core components of any computer system, installing and configuring of operating system and device drivers, analyzing the common hardware and software, causes and solution.

Basically there are two core components of any computer system and these are computers software and hardware components. Since software components as far as identifying computer components was concerned.

2.1.2.2 COMPUTER HARDWARE COMPONENTS

The monitor. A computer monitor is an electronic visual display for computers. A monitor usually comprises the display device, circuitry, casing, and power supply. The display device in modern monitors is typically a thin film transistor liquid crystal display (TFTLCD) or a flat panel LED display, while older monitors used a cathode ray tubes (CRT)

 

Figure 1:      LCD monitor

The computer case. It’s a form of case or box that gives protection to all the internal components of the computer. The computer case serves mainly as a way to physically mount and contain all of the actual components inside of a computer. Cases typically come bundled with a power supply.

 

Figure 2: computer case

Keyboard. A keyboard typically has characters like letters, numbers and special characters engraved or printed on the keys and each press of a key by a user typically corresponds to a single written symbol acting as an electronic switch. They are connected to the motherboard by either ps/2 ports or USB connectors on the computer case.

 

Figure 3: keyboard

The mouse. A computer mouse is a pointing device (hand control) that detects twodimensional motion relative to a surface. This motion is typically translated into the motion of a pointer on a display, which allows a smooth control of the graphical user interface.

 

Figure 4:mouse

CPU. A central processing unit (CPU) is the electronic circuitry within a computer that carries out the instructions of a computer program by performing the basic arithmetic, logical, control and input/output (I/O) operations specified by the instructions.it executes a program which is a sequence of stored instruction.

The mother board. is the main printed circuit board (PCB) found in general purpose microcomputers and other expandable systems. It holds and allows communication between many of the crucial electronic components of a system, such as the central processing unit (CPU) and memory, and provides connectors for other peripherals. Unlike a backplane, a motherboard usually contains significant sub-systems such as the central processor, the chipset's input/output and memory controllers, interface connectors, and other components integrated for general purpose use.

 

Figure 5:motherboard

Motherboard specifically refers to a PCB with expansion capability and as the name suggests, this board is often referred to as the "mother" of all components attached to it, which often include peripherals, interface cards, and daughter cards: sound cards, video cards, network cards, hard drives, or other forms of persistent storage; TV tuner cards, cards providing extra USB or FireWire slots and a variety of other custom components.

Power supply unit.  A power supply unit (PSU) converts mains AC to low-voltage regulated DC power for the internal components of a computer. Modern personal computers universally use switched-mode power supplies. Some power supplies have a manual switch for selecting input voltage, while others automatically adapt to the mains voltage. 

 

Figure 6:power supply unit

Cooling systems.  Electronic components generate alot of heat that is not healthy for the computer system hence different cooling components exist to ensure safety of the system. Such include a computer fan near the power supply and also the heat sink which draws heat from the processor.

Random access memory (RAM). is a form of computer data storage. A random-access memory device allows data items to be accessed (read or written) in almost the same amount of time irrespective of the physical location of data inside the memory. it’s a volatile memory i.e. it loses data when computer loses power. 

Read only memory(ROM). refers to memory that is hard-wired, such as diode matrix and the later mask ROM (MROM) which cannot be changed after manufacture. Although discrete circuits can be altered in principle, integrated circuits (ICs) cannot, and are useless if the data is bad or requires an update. 

Hard disk drive (HDD) is a data storage device used for storing and retrieving digital information using one or more rigid rapidly rotating disks (platters) coated with magnetic material. The platters are paired with magnetic heads arranged on a moving actuator arm, which read and write data to the platter surfaces. Data is accessed in a randomaccess manner, meaning that individual blocks of data can be stored or retrieved in any order and not only sequentially. HDDs are a type of non-volatile memory, retaining stored data even when powered off.

 

Figure 7:hard disk drive

Optical disc drive. (ODD) is a disk drive that uses laser light or electromagnetic waves within or near the visible light spectrum as part of the process of reading or writing data to or from optical discs. Some drives can only read from certain discs, but recent drives can both read and record, also called burners or writers. Compact discs, DVDs, and Bluray discs are common types of optical media which can be read and recorded by such drives.

2.1.3  DISASSEMBLING COMPUTER COMPONENTS

 

Tools required include Long Philip Screw Driver, Soft Wide Bristle Brush, blower, screw driver box etc.

•      Before opening the system case, turn off the system unit. Turn off and unplug the AVR from the wall socket as well. After that, unplug all the cables connecting to the back of the system unit. After clearing all the connected cables, put the system unit on an empty working table.

•      Touch the unpainted part of your system unit with your bare hands to remove the ESD of your body. This is an important part before opening your system case. You might destroy your RAM, Chipsets and other components of your motherboard.

•      Remove the screws of the side cover opposite to the side where the ports are. By most system cases, if you are facing the back of the system unit the right side cover is to be removed. Return the screws back to the screw holes to avoid losing them.

•      Once the side cover is removed, turn your system side down where the opened side of the system unit should be facing upward where you can comfortably look down on the inside of your system case.

•      The first thing we need to do is remove the power supply. To be able to remove the power supply, remove first the Molex connectors or the motherboard power connector, drive power connectors, the floppy drive power connector, the SATA power connectors and the four pin 12-volt motherboard connector

•      With the power supply removed, the data cable should be removed next. This includes IDE, SATA, and floppy drive cables. Secure the removed data cables.

•      Next I removed are the RAM, Video Card and other card peripheral components. Again have them secured in a safe place and put the screws back. Clean the connector edges of the card peripherals by rubbing the gold colored edge moderately with a rubber eraser then brushing off the shredding.

•      Remove all drives. This will include your hard drive, cd/dvd drives, and the floppy drive.

•      Since all peripherals where removed, the next thing to do is to remove the front panel connectors. This will include the USB, Front Panel (FP) and Audio header

•      After removing the header connectors, remove the motherboard. To remove the motherboard, locate first all the screws and lightly unscrew all screws alternately

•      Clean the system unit chassis with your brush, also clean your motherboard and 

                the           rest           of           the           peripherals           being          removed.

 

2.1.4 Assembling computer components

Since I had known the different core components of a computer and their functions. This activity was not so hard when assembling a computer. 

Required environment

Assembling a computer requires a safe and secure environment and the following factors should be considered when assembling a computer such as a large and flat working area, comfortable room temperature and an antistatic mat on the table, good ventilation and adequate light in work room, free from dust, environment etc.

2.1.5 Steps followed when assembling a computer

Step 1: open the case

I was pressing the side buttons on the cases while sliding towards me.

Step 2: install the power supply.

Install the power supply into the case to its alignment holes and specific placement with the holes on the case. Make the power supply firm by fixing using a screw driver.

Step 3: attach components to the motherboard.

it’s advisable to always attach the components to the mother board before attaching the motherboard to the case. 

Step 4: installing CPU and heat sink fan to the motherboard.

Align the CPU in connection 1 indicator lined up with pin 1 on the CPU socket and gently lower the CPU in the zero insertion (ZIF) socket. Then you close the CPU load plate and lock it by closing the load level.  Line up the heat sink/fan assembly retainers to the hole in the mother board. After place the heat sink onto the CPU socket being careful not to pin the CPU fan wires. Hence the sink power cable has been connected to the motherboard.

 

Step 5: installing RAM.

Align the notches on the ram module to the key in the slot and press downwards until the side tabs click into place and ensure that the side tabs have locked the RAM module. step 6: install the motherboard.

 Place standoffs in the computer case, these are used to mount   the motherboard and prevent it from touching the mental portions of the case. Align the I/O connectors on the back of the motherboard maintaining the openings at the back of the case. Align the screw holes of the motherboard with standoffs. After tighten the screws onto the case so that the motherboard is held firmly onto the case.

Step 7: install the internal drives.

Place the hard disk drive (HDD) such that it aligns with the 3-5-inch drive bay, ensure that its set to be the master on the IDE cable since each IDE cable can support up to two IDE devices such as hard drive, cd drive. This works when one of the device is made a master and another a slave and this must be configured in the BIOS after. Insert the HDD into the drive bay so that the screw holes in the drive line up with the screw holes in the case and screw them tight.

Step 6: install drives in the external bay

These include drives installed in the drive bays that are accessed from the front of the case and they include the optical drives.

Step 7: installing optical drive

Position the optical drive to align with the drive bay and place the optical drive into the bay so that the drive screw holes align with the screw on the case and connect the sound cable of the drive for the output of audio data to work well.

 

Step 8: installing floppy drive

Fix the floppy disk Drive (FDD) to align with the 3.5-inch drive bay and then place   the drive so that the screw holes align with the holes on the case. Make sure it is held firmly onto the case.

Step 9: installing adapter cards         

 These are used to add functionality to a computer system and they should be compatible with expansion slots. They include network interface card, wireless card etc. align the cards to their appropriate slots on the mother motherboard, then press it downwards gently until the card is seated and held tight.

Step 10: connect the internal cables

There are of two types of internal cables, power cable which distributes power from the power supply to the motherboard and other components. another internal cable includes data cable that transmit data from the motherboard components from storage devices like the hard drive. Power cables include 20 or 24 pin ATX power connector on the motherboard, SATA power connector on the motherboard that has a 15 pin connector connecting to the HDD, 4 pin berg power connector to the supply power to the floppy drive, 4 or 6 pin Auxiliary connector.

Step 11: Re-attach side panels and connect external cables

After all the internal components have been installed and connected to the power supply and motherboard, I then re-attached the side panels to the computer case. Then finally you fix back the external cables such as mouse, keyboard, serial cable for the monitor, PS/2, a male power connector, USB connector for peripherals such as scanners, printers, speakers, Ethernet Rj45 connector etc.

 

 

 

2.2 DESIGNING A WEBSITE USING WORDPRESS

2.2.1 INSTALLING WORD PRESS

1.   Install WAMP

In the PHPmail option while installing WAMP, leave it as it is

2.   Now extract the WordPress.zip. Create a folder under C:\wamp\www name it as

WordPress copy all the files and folders under WordPress folder in C:\wamp\www

3.   Start WAMP and start all the services by left clicking on it in the task bar.

4.   open your web browser

5.   Open http://localhost/

6.   Click on PHPMyAdmin and create a database for your WordPress install.

(Alternatively, simply click on the WAMP’s icon in the taskbar and then click on PHPMyAdmin option as shown in the following screenshot)

The screenshot given below describes how to create a database within the PHPMyAdmin page.

 

Figure 8: screenshot of how to create a database.

6.  Open http://localhost/wordpress and click on create a configuration file.

Now Enter the details as mentioned.

•       Database name: Database name you have created (WordPress)

•       Username: root

•       Password: Leave it blank

•       database host: Keep it default (Localhost)

•       Database prefix: Keep it default (wp_) 

 Click on Submit. On next screen click on Run setup.

7.  On the next screen add Blog title and Email. Search visibility will not matter here as we are working on the Local environment.

8.  On the next page, copy the password and save it. Click on login and login with the password on the screen and username as admin. (As shown below in screenshot)

2.2.1.1     Creating a website                                                                                                                                                 

In order to edit my website in WordPress, I had to be on the sites dashboard where the page, blog posts, media, comments, plugins and also themes were shown.  

Adding a page                                                                                                                                                            The following steps were taken to create a page.                                                                                              I clicked on page, wrote the title for the page and then also wrote what I wanted to be on that page in the text panel, and then clicked save and publish. The page was created.

Adding a blog post                                                                                                                                               The following steps were taken to create a page.                                                                                                       I clicked on blog posts, then wrote the title for the post, and then also wrote what I wanted to be on the post in the text panel, then clicked save and publish. The post was created.

Installing WordPress themes manually.

•       I downloaded WordPress themes for the website. I have the WordPress themes as a folder 

•       So I Uploaded the zip file to /wp-content/themes/ and unzip it. 

•       Place it in the themes (/wp-content/themes/) directory, and activate it via Admin - Appearance - Themes 

 

 

2.3 Configuration and installation of windows 7 operating system.

Things to consider include a windows 7 operating system, Optical drive/ external optical drive, USB flash disk, Back up your important files and data.

2.3.1 Installing windows 7 operating system from a DVD

1.    To run the installation disc, insert the Windows installation disc into the DVD drive.

2.    Restart your computer.

3.    When the Press any key to boot from the CD or DVD message appears, press any key to continue.  If the disc does not begin to run, press your computer's Power button and press the F12 key to load the Boot menu

4.    When Windows 7 Setup appears, confirm that the Language, Time, Currency and Keyboard Method fields display the correct settings.

5.    On the Windows 7 Installation dialog box, click Install Now.

6.    Review the license agreement, and click I accept the license terms.

7.    On the Which type of installation do you want? window, click Custom (advanced).

8.    On the Where do you want to install Windows window, select the largest internal disc as the Primary Partition, then click Next. If the Primary Partition shows 0GB free, select Unallocated Space and click Next.

9.    Your computer will restart.

10. Personalize and customize your Windows 7 operating system by following the instructions on the following screens.

11. When your Desktop screen appears, you are ready for the next step.

2.4 Windows server 2008 R2

Installing windows server 2008 R2

Installing windows server 2008 R2 is somehow like installing windows vista. It is easier to install it than other types of operating systems like windows. windows server 2008 R2 requires a processor of 1GHZ (x86 processor) or 1.4GHZ (x64 processor) but a recommended one is 2GHZ or faster note. It also requires a minimum memory of 2 GB for a 32 bit systems or a 4GB standard or 64 GB for enterprise and data center, it also requires an available disk space of a minimum of 10 GB but its recommended 40 GB or more. It needs also a DVD-ROM drive and a super VGA (800 x 6000)

The following steps should be taken into place when installing a windows server 2008 R2;

1.    Restart the computer and then press F8.

2.    Enter into the BIOS setup to make the computer boot from DVD.

3.    Insert Microsoft Windows Server 2008 R2 bootable installation media.

4.    Once inserted, reboot the computer. 

5.    On the Install Windows screen, click Next. 

 

Figure 9:screenshot of installation of windows server 2008 R2

6.    On the next page, click Install now.

7.    On Select the Operating System you want to install page, from the displayed Windows Server 2008 R2 editions, select the appropriate edition that is to be installed. 

8.    On the next page, type the 25-character product key and click Next.

9.    On Please read the License terms page, check I accept the license terms checkbox and click Next.

10. On Which type of installation do you want page, click Custom (advanced). 

11. On Where do you want to install Windows page, ensure that the hard disk drive on which Windows Server 2008 R2 is to be installed is selected.

12. Once selected, click Drive options (advanced). 

13. From the enabled options, click New to create a new disk drive partition.

14. On the Size field, specify the size of the new volume in MB. 

15. On the displayed Install Windows message box, click OK.

16. Back on the same page, click to select the hard disk drive partition (E. g. Disk 0 Partition 2, in this demonstration) where Windows Server 2008 R2 is to be installed and click Next.

17. On the Installing Windows page, wait till the Windows Server 2008 R2 installed and the computer get restarted. 

18. After second restart, on the displayed screen, click OK to change the user password before logging on for the first time.

19. On the available fields, type and retype the new password and press Enter. 

20. On the next confirmation screen, click OK to log on to the Windows Server 2008 R2 computer.

2.5 NETWORKING 

This is the connection of two or more nodes that can communicate with each other either with a physical connection or wireless connection like printers, computers, scanners, and other devices with the help of the Ethernet cables. 

2.5.1 TRANSMISSION MEDIA

2.5.1.1    TERMINATION 

 

They are types of cable clipping or termination, the cross over cable, straight through cable, roll over cable. 

 

 

 

 

 

 

           

Table 1                                                                                                     Table 2

Side A              Side B

 

Side A              Side B


White-green

White-Orange

White-green

White-green


Green

Orange

Green

Green


White-Orange

White-Green

White-

Orange

White-Orange


Blue

Blue


Blue

Blue


White-Blue

White-Blue


White-Blue

White-Blue


Orange

Green


Orange

Orange


White-Brown

white-Brown


White-Brown

White-Brown


Brown 

brown


Brown

Brown


 


Cross over cable                                             Straight through cable

 

 

                                    

2.5.1.2    NETWORKING DEVICES

A. ROUTER


 

 

Figure 10: router

It is an electronic device that operate at the third layer of the OSI model, it forwards data packets between computer networks. A router is connected to two or more data lines from different networks (as opposed to a SWITCH which connects data lines form one single network). A router has 4 Ethernet ports and each port represent a network, serial ports (number depends on the type of a router) to connect a router to a router and a console port for configuration.

How routers work 

A router uses IP addresses to figure out where to send packets. If two hosts from different networks want to communicate, they will need a router between them to route packets 

 

Figure 11 showing how routers work.

Host A and host B are on different networks. If host A wants to communicate with host B, it will have to send a packet to the router. The router receives the packet and checks the destination IP address. If the destination IP address is in the routing table, the router will forward the packet out the interface associated with that network. 

 

B. SWITCH

 

Figure 12: Switch

It is an electronic device that operate at the second layer of the OSI model, it connects devices together on a computer network, by using packet switching to receive, process and forward data to the destination device. A switch has 24 ports plus a console port. A switch forwards data only to one or multiple devices that need to receive it, rather than broadcasting the same data out of each of its ports. A switch connects data lines form one single network.

 

 

 

 

How switches work 

 

Figure 13 showing how a switch works.

  

Host A is trying to communicate with Host B and sends a packet. A packet arrives at the switch, which looks at the destination MAC address. The switch then searches that address in its MAC address table. If the MAC address is found, the switch then forwards the packet only to the port that connected to the frame's destination. If the MAC address is not found, the switch will flood the frame out all other ports. To learn which MAC address is associated with which port, switches examine the source MAC addresses of the receiving packet and store that MAC addresses in their MAC address table. 

 

C. HUBS  

A hub serves as a central point to which all of the hosts in a network connect to. It is an OSI layer 1 device. It receives a signal from one port and sends it out to all other ports. Sometimes it is called a multiport repeater 

 

 

 

Figure 14: Hub

 

These devices are considered obsolete and switches are commonly used instead. Hubs have numerous disadvantages. They are not aware of the traffic that passes through them. They create only one large collision domain. A hub typically operates in half duplex. There is also a security issue with hubs since the traffic is forwarded to all ports (except the source port), which makes it possible to capture all traffic on a network with a network sniffer! 

D. CONFIGURATION

Configuration of the router and switch had been performed in the switching and routing labs, where the use to give us a router, a switch and a pc and I was given time to configure them depending on what they taught us. It has helped me to know how those devices work and operate and how to configure them (by giving them IP addresses).

An example of a protocol I configure include:

OSPF (open shortest path first protocol) which is used to enable communication between different networks. The OSPF works in areas under autonomous systems (systems under one administration). It is unlimited in term of routers compare to RIP (routing information protocol) reason why it is mostly used by most of the ISP (internet service provider) such as MTN, ORANGE…it has three technologies (DR, BDR, wild card mask)

 

The figure below shows how to configure the OSPF protocol on router0

 

Figure 15 showing how to configure the OSPF protocol

This is how it is configured;

Router0>en

#config t

#int s0

#ip add 198.162.1.1 255.255.255.0

#clock rate 64000

#no shut

#router ospf 100

#network 198.162.1.0 0.0.0.255

#end

 

 

2.6  GRAPHICS AND DESIGN

2.6.1 ADOBE PHOTOSHOP

Adobe Photoshop CS6 is a popular image editing software that provides a work environment consistent with Adobe Illustrator, Adobe InDesign, Adobe Photoshop and other products in the Adobe Creative Suite. 

2.6.2 LAUCHING ADOBE PHOTOSHOP CS

Installed the software, then click on computer-local disk- program Files-Photoshop and click it then the software window appears.

2.6.3 CREATING A PROJECT

Click on file, new project or u can press CTRL + N

2.6.4 CUTTING A PHOTO

Use a marquee tool, move the tool around the part you want to cut and then press delete.

2.6.5 HOW TO DELETE BACKGROUND

Click on the image, trim it and then click transparent and then click ok.

2.6.6 BRUSHING ROUGH OBJECTS

Click on blur, reduce on the radius of the image and then hold the right click button and then start brushing.

2.7  ILLUSTRATOR

2.7.1 DESIGNING A CALENDER

Open a new document, go to tools and click shapes

Choose the shape that you want and drag and draw it in a new document.

Then start filling it with text, images and numbers depending on what suites you.

2.8 MOODLE

 

Moodle is a Learning Management System (LMS), being used at several educations and schools. Moodle has been chosen as the system where information, materials and assignments related to courses as well as information from secretaries and teachers can be found. Moodle is an Internet based system, which means that if you have access to the Internet then you have access to Moodle.

2.8.1 INSTALLATION

First install a wamp server an d a web browser if it is not install.

Download a Moodle software and extract it in the wamp directory and choose a file name. Click on PHP MY Admin and create a database 

Then click on local host. Click on the file name in the wamp directory displayed and then continue with the installation process. Enter login information i.e. username, host, password and then click ok.

2.8.2 ENHANCING THE MOODLE

In order to edit in Moodle, the editing settings had to be turned on.                                                                          Uploading files; clicked on add activity and resource, find and uploaded a file then browsed from the computer and save.

Creating courses: Firstly I created a category, clicked on courses and went to new category  and typed the course name. Adding a sub-category to create a course unit, clicked on  create and filled in the details then saved.

Adding online quiz: Under the course unit, clicked on activity or resource then choose the quiz and saved. Uploading questions in the question bank under settings, clicked on question bank and go to import to upload the questions.

Adding a block: I went to home page and checked on add a block, choose the block I wanted for example 

on line users and clicked on add

Creating a course                                                                                                                                                      

I went to creation and created a course category, add a new category and gave it a category name and added a description and clicked on create then checked sub category and then create a course.

Uploading notice                                                                                                                                                      

I went to course and choose one course, clicked on upload notice and to add activity and resource then file, added a name and description then went to upload.

Enabling self-enrollment                                                                                                                                          

I went to edit settings, under users and clicked on enrollment settings. Clicked on XQt and then clicked on go.

        

How to create a student’s account                                                                                                                           

Under the home page I went to site admin, went to users and then accounts and went to add users, gave the name and description then clicked add.

How to add a banner                                                                                                                                               

On top, I went to add activity and resource, went to table then find the image and clicked ok.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 CHAPTER THREE

ACHIEVEMENTS AND CHALLENGES

3.1 ACHIEVEMENTS

•      Working with the field team has given me a chance to learn and gain experience on the activities they carry out and the challenges they encounter in the field.

•      Through this programme I had the chance to interact with most of the staff members in the organization and we have been able to share ideas and views.

•      This programme also enriched my Curriculum Vitae in a way since I was able to acquire a certificate in community based reproductive health.

•      I learnt how to configure a router.

•      I learnt how to subnet a network.

•      I learnt how to install operating systems.

•      I was able to improve my Computer care and maintenance skills.

•      I learnt how to manipulate records in a database, how to create a database in MySQL server and in wamp server and the operations that can be performed on the database

•      I can identify the components, hardware and software of the computer I also leant how to come up a working computer just from scratch.

•      I also acquired more skills in installing different operating systems, devices, and drivers and among other software.

•      I also gained more knowledge in computer care and maintenance.

•      It also helped me to gain Experience in my area of study since I have been working with already professional skilled workers of the Company.

•      Have become a better team Player than before

 

 

 

 

3.2  CHALLENGES

The biggest challenge faced during the training was that of the inadequate funds to sustain the daily activities of the field training satisfactorily. High costs of breakfast lunch and transport to and from the work place were met. This was however overcome by using the internship funds sparingly and for their intended purpose. Financial support was also sought from parents and relatives to ensure smooth learning.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4 CHAPTER FOUR

 

RECOMMENDATIONS AND CONCLUSION

4.1 RECOMMENDATIONS

4.1.1 THE UNIVERSITY

The University has to continue with the improvement and upgrading its curriculum to fully suit the market dynamics. More emphasis needs to be put on the practical lessons and the theoretical concepts as well. This will ultimately improve on the students’ internship performance.

The university Should provide some internship money to the internees so that it increases on the facilitation fund to avoid financial difficulties during the period of internship.

4.1.2 THE STUDENTS FOR FUTURE INTERNSHIP

Students need to develop a keen interest in modern employment literature so as get an insight prior to field attachment. The literature would also enable students to get more used to the basic terms and concepts for example the compendium to reduce on the difficulty to fully understand the various concepts used in the employment setting

Students should take internship training seriously as they do to lectures at the university as well as respecting their field supervisors together with university supervisors and fellow students since they are some people they are meet in the work place.

Furthermore, student should budget for their finances and use the small facilitation (funds) accordingly and sparingly not to meet financial difficulties during the period. This will help them to meet their expenditure accordingly.

4.1.3 THE ORGANIZATION.

It is our prayers that the organization can provide a minimal allowance to enable the interns meet the high costs of living. 

The organization should increase internet access in all departments. This can be through boosting the WI-FI server at the resource center to cover the entire organization.

4.2 CONCLUSION

I would like to conclude that this internship programme has been worthwhile for me and I have benefited in a number of ways including a chance to learn about most of the activities in information technology and to work and learn from the experts in the fields of technology. I have learned and gain a lot from this programme. And I have also learned that teamwork and commitment are very much important in internship program. And I would also like to mention that this programme had also given me some new perspectives that I did not come across during my studies back the University. All in all, it has been a great experience working with the organization, and it has given me insight on how to shape my career for greater responsibilities in the near future. Thanks again to Afrosoft IT solutions limited as an organization, staff and everyone who directly and indirectly contributed to the success of this programme and the support that they gave me. And I would like to emphasize that I’m very much thankful of the field supervisors I worked closely with for seeing to it that I finish this programme equipped with more knowledge and skills. It is through their (supervisors) support, commitment, efforts, patience, and interests that I learned and gain experience in most of the activities I undertook. The programme couldn’t have been easy without everyone’s efforts to make it a success. 

 

 

 

 

 

 

Comments

Popular Posts